The filter cover door will automatically begin to close as the new filter is inserted. All other trademarks are owned by their respective companies. If the light continues to flash, your optics are either blocked in some way or they need to be replaced. The ice-maker will start the harvest cycle. To test this precious thermostat one needs only to stick it into a freezer and let it hang out for an hour or so. This will likely resolve the issue.
Being an engineer, I am pretty good with appliance repair, and usually have the solution and it fixed in a short amount of time. The second one always has a problem with the water valve. Nest ® and Nest Learning Thermostat ® are trademarks licensed by Nest Labs, Inc. If the mold where cubes are made is flaking or corroded it is time for a new ice maker assembly. Why you should turn your ice maker off If the water supply is not connected to water supply line turn the ice maker off.
Double checked everything with continuity meter, all good! Here is what I found when I pulled off the harness protection: Here is the repair before I retaped and put back the harness protection: Soldered the connections and used some marine-grade heat shrink. Then I measured for continuity between the plug at the top of the freezer and the bottom. Tape the door on the receiver closed and don't block the beam. Wow, thank you for posting this thread! We have the Refrigerator Use Guide and a list for Troubleshooting your. When your Whirlpool Gold Series Refrigerator is not working properly, this page will assist you in finding and fixing the problem. Open the freezer door make sure that the freezer door has been closed for a minimum of 10 seconds prior to opening the door. Use a towel to wipe up any spills.
Dealer alone determines actual price. Our chat service hours are Monday - Friday from 8 a. Unplugged for 10 minutes and then plugged back in. Straighten the water source line to restore adequate water flow and pressure. I cannot find the door harness separately, so I am assuming it was Foamed In Place.
We may receive compensation when you click on links to those products. Thewater dispenser works just fine, producing cold water with no issues. All was working great until a few weeks ago when the icemaker stopped producing ice. Result: You should see two flashes and a one second delay repeating. Remove the side cover on the side module by pulling off.
Mechanically, this is a Whirlpool modular ice maker with a few extra trim pieces, different fill tube location, and a set of control boards have replaced the bail arm switch. I also defrosted the freezer side for a whole hour with thedoor open to see if something was clogged. A clogged or incorrectly installed water filter will reduce the water flow to the ice maker and could cause thin, low or no ice production. Do you have any more suggestions?? First, use our troubleshooting tool to diagnose your problem. The ice slowly moves around and drops out. Next, check to make sure there are no kinks in the water supply line.
It is not filling up with water, and a while ago I did have a frozen fill tube, which I thawed out with a hairdryer. I did it once, and now I do it three times. Verify that the ice maker is turned on. When adjust mode is activated, adjusting information will appear on the display screen. I used two ice makers, and the first one was a computer version that didn't work.
Push the button in completely for 1 second each time. Disconnect the electrical plug by lifting the clip on the plug. I gave it a shot. Post 2002 Diagnostic Tests: Note: The ice bin must be installed on the door to activate the left side flap, ice should not be over the top notches of the bin. It's only function is to get it on.
Near the end of the cycle a the ice maker calls for water and fills the mold and the whole thing starts again. I wonder if there is a fault interlock for the door being open too long, and will shutdown the icemaker to allow the ice to refreeze and then it will reset itself? Remove the bottom shield by removing the 3 screws on the bottom. Note: Any images or third-party logos on this page belong to their respective copyright holders and are used for informational purposes only. Remove jammed ice from the ejector arm using only a plastic utensil so the ice maker is not damaged. Do not force the wire shutoff arm up or down. I will post a picture of the 'before' if I get a chance. The white and blue were also nearly severed.